Led strip light 5050 rope light and what is the difference between 5050 and 3528

March 01, 2023

5050 patch introduction
5050 patch is an electronic component, the size is 5mm * 5mm * 1.6mm, the light intensity can reach 5500-6000MCD (pure white light, slightly warmer light), the working voltage is the same as ordinary LED, only 3.2-3.4 V, the current is the same, 60MA.

5050 led package size: 5mm * 5mm * 1.6mm, light intensity can reach 5500-6000MCD (pure white light, warm light slightly smaller). His working voltage is the same as ordinary LED, only 3.2-3.4V, the current is the same 60MA.

Because the 5050 patch led volume is relatively small, the workmanship is relatively fine, so manual soldering is not convenient, but it is not said that it can not be soldered, its soldering temperature should be controlled within 250 degrees, otherwise it will burn the more expensive 5050 patch led.

Because the 5050 patch led parameter determines that he must be a favorite led, so he is often used in high-end civilian energy-saving lamps, car dashboards, led lights, cell phone backlights and buttons, instrumentation backlights and require small-volume LEDs Products, LED backlight, switch and logo flat backlight, caller ID, flash, car, audio, indoor display, lighting market!

LED strip light

LED strip light
5050 chip power
The higher the current, the higher the voltage, the higher the temperature, the smaller the current, the angle of illumination: 125 degrees, etc.
The forward current is 60mA, and the reverse voltage cannot exceed 5V.
The working temperature is preferably between -35 and +60 °C. If you do not consider the light decay life problem, you can also work below +85 degrees.
Power: 0.18W (same power as 0.2W on the market)

5050 patch character
1. current: 43-46mA (this is the most ideal drive current); the maximum operating current can not exceed 60mA;
2. the voltage 2.8-3.6V (requires the instantaneous voltage of the lamp bead can not exceed 5V, or the LED lamp bead is damaged or seriously damaged and cannot be repaired);
3. the ambient temperature -20 ° C ~ +40 ° C (requires the heat dissipation design of the lamp is better done, the temperature of the LED lamp pin can not exceed 60 degrees);
4. If the current is at 14-20 mA, the brightness is reduced by 4% for each 1 mA reduction;
5. The current is 0.12W at 43-46mA, 0.15W at 46-53mA, and 0.18W at 54-60mA;
6. low power consumption
7. long service life
At the right current and voltage, LEDs can last up to 100,000 hours.
8. high brightness, low heat
Less heat radiation than HID or incandescent lamps.
9. environmental protection
LEDs are made of non-toxic materials, unlike mercury-containing fluorescent lamps that can cause contamination, and LEDs can be recycled.
10. sturdy and durable
The LED is completely encapsulated in epoxy, which is stronger than both the bulb and the fluorescent tube. There are no loose parts in the lamp body. These features make the LEDs hard to damage.
11. strong controllability
It is easy to achieve color changes and light and dark changes, and it is responsive.

The difference between LED Light strip 5050 and 3528

The 5050 strip and the 3528 strip are actually the difference in the size of the internal bead chip. The 5050 led light strip indicates that the lamp bead chip has a length of 5.0 mm and a width of 5.0 mm. Similarly, the led light strip of 3528 indicates that the length of the lamp bead is 3.5 mm and the width is 2.8 mm.

LED strip light

The above is the Led strip light 5050 rope light and what is the difference between 5050 and 3528 we have listed for you. You can submit the following form to obtain more industry information we provide for you.

You can visit our website or contact us, and we will provide the latest consultation and solutions

Share to:

Send Inquiry

Previou:Factors affecting LED Light Decay and quality of LED lamps